wibako

Brak wolnej jazdy Kobelco SK210LC-6E

Moderator: MARIO/MECALAC

Brak wolnej jazdy Kobelco SK210LC-6E

Postprzez Ambrozy » 25 Sie 2019 11:48

Marka i model maszyny: Kobelco SK210LC-6E
Rok produkcji: 2003
Numer seryjny: YQ08-04667

Witam.

Jak w temacie: Kobelco SK210LC-6E brak możliwości zmiany prędkości jazdy. Pali się ikonka żółwia, klawisz zmiany prędkości działa jednak brak reakcji. Założony nowy sterownik, oryginalny skradziono. Na pewno nie jest skonfigurowana do końca.
Serwomotor oraz cięgno gazu wyregulowane, skalibrowane. Brak błędów elektrycznych, wszystkie czujniki działają, są odczyty na wyświetlaczu. Ktoś obeznany ze starymi koparkami gąsienicowymi Kobelco pomoże?

Pozdrawiam Ambroży.
Jeśli pomogłem kliknij pochwała

ıɯɐƃou ʎɹoƃ op ɹoʇıuoɯ zsɐɯ ǝz ʎzɔɐuz oʇ ɔɐʇʎzɔǝzɹd oʇ ǝıuɐʇs ʍ sǝʇsǝɾ ılǝzǝɾ

Awatar użytkownika
Ambrozy
Operator

  • Posty: 253
  • Rejestracja: 11 Mar 2007 17:37
  • Miejscowość: google
  • Pochwały: 17

Reklama

simmet

Brak wolnej jazdy Kobelco SK210LC-6E

Postprzez Michał PHU » 01 Wrz 2019 16:39

Czy usterka nastąpiła po wymienia sterownika? Mechatro kupione od chinczyka czy oryginał?
Czy w historii błędów masz może błąd nr. 28 Travler 2-speed solenoid?
W jaki sposób skalibrowałeś governor?

Michał PHU
Fizol

  • Posty: 24
  • Rejestracja: 04 Wrz 2017 10:05

Maszyna: Hydrema R 1800

Firma: PHU Michał


Re: Brak wolnej jazdy Kobelco SK210LC-6E

Postprzez Ambrozy » 04 Wrz 2019 19:15

Witam.
Czy usterka nastąpiła po wymienia sterownika?
- tak.
Mechatro kupione od chinczyka czy oryginał?
- kupione w USA przez znajomego, raczej oryginał poprawka 100% chińczyk
Czy w historii błędów masz może błąd nr. 28 Travler 2-speed solenoid?
- nie.
W jaki sposób skalibrowałeś governor?
- w/g procedury:
1. While keeping the work mode selector switch on the cluster gauge pressed, turn the starter switch ON, hold it in this condition for 5 to 10 seconds, and release it.
2. The governor motor returns it to the starting point, and it stops at the point corresponding to the accel dial set position.
3. Keep the buzzer stop switch on the gauge cluster pressed for 5 to 10 seconds and release it, and STEP 1 is displayed on the multidisplay, then wait until the next display STEP 2 appears.
4. After verification of the STEP 2 display, go to the engine room and adjust the rod Assy standard length to Bmm in order to have the clearance "A 0.1mm" between the governor lever and the engine stop set bolt. If governor motor was replaced, indicate STEP 2 display and insert rod assy.
• Dimension B:
186 mm (SK160LC-6E),
288~304 mm (SK210LC-6E),
165 mm (SK250LC-6E),
210~213 mm (SK290LC-6E)
5. Press the buzzer stop switch once, and wait until the STEP 3 is displayed.
6. After verification of STEP 3 display, starts the engine. Then, it is unaffected by the actual accel dial position.
7. Press the buzzer stop switch once, and the STEP 4 is displayed and the controller returns from the A position of governor to the low idling position once, and then reads the engine rpm to the high idling automatically. (Required time : about 2 minutes.)
8. After completion of the read out, wait until the "CPU FINISH 2220RPM" is displayed on the multidisplay. After the "CPU FINISH 2220RPM" is displayed, the controller returns to the actual dial initial optional position automatically.
Note : If the "CPU FINISH 2220RPM" is not displayed, the adjustment has failed. Turn the starter switch off, and per-form the adjustment again.
9. When the screen "CPU FINISH 2220RPM" is displayed after adjustment of engine, the "CPU STEP 5 MEMORY" is displayed automatically, the engine speed changes into high idling and the pump is loaded, and then "CPU FINISH ORPM" is displayed after 1 minute in high idling condition and adjustment is terminated.
Jeśli pomogłem kliknij pochwała

ıɯɐƃou ʎɹoƃ op ɹoʇıuoɯ zsɐɯ ǝz ʎzɔɐuz oʇ ɔɐʇʎzɔǝzɹd oʇ ǝıuɐʇs ʍ sǝʇsǝɾ ılǝzǝɾ

Awatar użytkownika
Ambrozy
Operator

  • Posty: 253
  • Rejestracja: 11 Mar 2007 17:37
  • Miejscowość: google
  • Pochwały: 17

Wyświetl posty z poprzednich: Sortuj według

Kto jest na forum

Użytkownicy przeglądający to forum: Brak zarejestrowanych użytkowników oraz 6 gości

nazwa

tekst alternatywny × Nie pokazuj więcej